PSL Whole House Repiping delivers professional whole house repiping throughout Okeechobee, FL, for persistent water line problems.
Licensed Experience
15+ years of whole-house repiping experience
Wide Service Coverage
500+ happy customers throughout Port St. Lucie
Fair Pricing Scheme
Full house repipes quoted by square footage and fixture count
No Unnecessary Disruption
24-48 hours of average water restoration time
Local Compliance
100% St. Lucie County permit pass rate for all our repiping work
Free Pipe Assessment
Free on-site material assessment for all pipe types and conditions
Get a FREE Quote

These stressed homeowners were dealing with rusty water and weak pressure from their property's aging galvanized pipes. So, for the whole 1,400 sw. ft. house, we replaced 160 feet of corroded galvanized supply lines with 185 feet of new PEX piping. We also updated all shut-off valves and fittings for the bathrooms, kitchen, and laundry area.
PRICE: $5,400
COMPLETION TIME: 3 days

The aging water pipes under this single-story 1,500 sq. ft. home in Cypress Quarters have caused several recurring leaks. It wasn't good for the wood, the water bill, or the homeowners' water access. Repairs at this rate would just be a plaster fix and wouldn't solve the problem long term. With the client's approval, we replaced the old supply lines with 200 feet of new red and blue PEX piping. Our work covered both bathrooms, the kitchen, and the laundry area.
PRICE: $5,800
COMPLETION TIME: 3 days

The lovely homeowners of this larger home along State Road 70 called us about the occasional leaks in different parts of their house. Knowing that it's been a long time since their plumbing was checked and updated, we were asked to assess it. There were aging copper pipes throughout the house. So we planned new pipe routes around existing plumbing connections and replaced the old supply lines with 300 feet of new PEX piping.
PRICE: $8,200
COMPLETION TIME: 4 days
Cold water lines carry water from the point where it enters your home to nearly every faucet, toilet, and spigot you use. When one section fails, the others are often close behind, especially in homes that have had several spot repairs. We encounter this a lot in Lakewood Park, FL. We replace the cold side on its own when the hot lines are still healthy. It's a setup we see often in neighborhoods like Cypress Quarters and Basswood Estates.
Galvanized steel is usually the reason older Okeechobee homes lose pressure over time. Back in the 1930s, the city was a busy shipping hub for winter vegetables, and plenty of houses from that era and the rebuild after the 1928 Okeechobee Hurricane were plumbed with steel pipe. Rust builds up inside until the flow drops to a trickle. Our crew removes or bypasses those lines and runs new supply pipe to each fixture.

Polybutylene tends to hide in homes built from the late 1970s through the mid-1990s. The gray plastic breaks down from the inside as chlorine works on it, so there’s rarely any warning before a line splits. PSL Whole House Repiping traces every run and replaces it in one planned project, rather than chasing leaks one at a time.
Copper is both a material we replace and one we install, depending on its condition. Older copper can develop pinhole leaks after years of service, while new copper gives you a rigid metal system with a long track record. Our plumbers explain the trade-offs against PEX so you can choose what fits your layout and budget.
Emergency repiping is for the days when several lines fail at once and patching simply won’t hold. We stop the active leaks first, then lay out a replacement plan so your water is back as soon as possible. With US 98, US 441, and State Road 70 all running through town, our crew reaches homes across Okeechobee fast for emergency house repiping.
A targeted fix is the right call when the damage stays in one spot, and the rest of the system is in good shape. Leaks in several rooms or pressure dropping at multiple taps usually point the other way. We’ll give you an honest recommendation either way, even if that means a smaller job for us.
A repipe is the perfect time to handle other plumbing projects that depend on the same lines. New fixtures, a water heater swap, or main line work all go more smoothly when the pipes behind them are fresh. Our team helps you decide what should come first, so you’re not opening the same wall twice.
Being upfront about what a repipe won’t fix matters to us. New supply lines solve pressure problems, rusty water, and recurring leaks, but they won’t fix a slow drain or a worn-out faucet cartridge. If we spot an issue outside the repipe scope, we’ll point it out so nothing catches you off guard.
Steadier pressure is usually the first change homeowners notice after a repipe. Running the shower while the washer fills stops being a gamble. In a humid subtropical climate where summer heat bakes attic lines for months, fresh pipe also holds up far better than the aging lines it replaces.
Fewer repair calls come naturally once the worn-out sections are gone. Homes along Taylor Creek and closer to the lake already deal with plenty of moisture, so a hidden leak is often the straw that breaks the camel’s back for drywall and cabinets. Replacing the whole system lets you stop bracing for the next drip.

A full repipe in Okeechobee usually costs between $4,000 and $15,000. Partial projects tend to land around $2,500 to $5,000, depending on home size and pipe material. Most whole-house jobs take 2 to 4 days, and we put the price in writing before any work starts.
Homes inside city limits go through the City of Okeechobee for repiping permits and inspections, while properties outside may follow county requirements. We confirm which applies before the job begins. When the work passes inspection, we give you a record of everything replaced, which helps with insurance and resale down the road.
Reach out to PSL Whole House Repiping to schedule an inspection anywhere in Okeechobee. We’ll check every line and hand you a written plan so you can move forward with confidence.
© 2026 All Rights Reserved | PSL Whole House Repiping